Industries / 11
Biotechnology
Biotech equipment is small compared with a pressure vessel, but the tolerances and documentation are tighter. K999 fabricates bioreactor and fermenter support skids, media and buffer manifolds, sampling and transfer pipework, and cleanroom steelwork in 316L, with orbital welding and surface finishes suited to single use and multi use processes.

Clean, small and precise
Bioreactor skids, hygienic manifolds and small bore stainless assemblies built to tight tolerances, low hold up volumes and validated cleanliness.
In a bioprocess line, every millilitre of hold up matters and every crevice is a contamination risk. We fabricate manifolds with short runs, minimal dead legs, clamped or orbital welded connections per the client standard, and drain points that actually drain, working from a piping model rather than hand sketches.
Small bore work demands a clean shop and disciplined handling: dedicated stainless tools, controlled purge, and protection of polished surfaces from the moment a part is finished. Skids are assembled with instruments, valves, pumps, cable routing and supports so the unit arrives tested and ready for commissioning, with the connections clearly tagged.
Because equipment often supports validation activity, documentation includes material certificates with heat numbers, weld logs, surface roughness measurements, passivation and cleanliness records and as built drawings. Where the client's quality system requires it, we attend joint inspections and provide the evidence needed for installation and operational qualification.
What we fabricate
- Bioreactor and fermenter support skids
- 316L hygienic manifolds and small bore pipework
- Orbital welding with purge control on all joints
- Sampling, transfer and buffer preparation assemblies
- Cleanroom frames, benches and equipment supports
- Surface finish measurement and passivation records
Typical applications
- 01Biologics and vaccine process suites
- 02Pilot and clinical scale fermentation
- 03Media and buffer preparation areas
- 04Single use support frames and bag holders
- 05Laboratory and R and D process rigs
- 06Cell culture and purification skids
bioreactor skid fabrication Thailand / biotech stainless fabrication / hygienic manifold fabrication / small bore orbital welding Thailand / 316L skid fabrication Rayong / buffer preparation skid fabrication / cleanroom equipment fabrication / single use support frame fabrication
Biotechnology FAQs
Questions we are asked
Ten detailed answers on biotechnology fabrication, testing, delivery and documentation.
Bioreactor and fermenter support skids, media and buffer preparation manifolds, sampling and transfer pipework, small bore hygienic assemblies, single use support frames, bag holders, cleanroom benches and equipment supports in 316L.
Small bore lines have small volumes and short runs, so weld quality, purge and cleanliness matter more than tonnage. We work in a clean area with dedicated stainless tools, control purge on every joint, and protect polished surfaces from the moment the part is finished.
Yes. Manifolds are laid out with short branches, close coupled valves and minimal dead legs, and assemblies are built from a model so the geometry is decided before cutting. Drain and sample points are positioned where they will actually work.
With material certificates and heat numbers, weld logs, surface roughness measurements, passivation and cleanliness records, pressure or leak test certificates and as built drawings. Joint inspections can be attended where the client's quality system requires them.
Yes. Frames, holders, trolleys and supports are fabricated in stainless with polished or mill finish, designed for the loads and handling method the process uses, and built with no crevices that would trap spillage or cleaning fluid.
We weld hygienic small bore and medium bore pipe orbitally with recorded parameters, verified purge and inspection by borescope on request. Weld maps tie each joint to its record so the loop can be released for use with evidence behind it.
Yes. Pilot and clinical suites usually need small, precise, well documented equipment rather than large tonnage, and that is the kind of work we handle comfortably alongside larger process packages.
Finished surfaces are handled with clean gloves, protected with film or capping, and packed so parts cannot rub together. Openings are sealed and internal inspections are recorded before the item is closed for transport.
Yes. Where a skid interfaces with vendor bioreactors, filters or analysers, we build to the vendor interface drawing so connections, heights and clearances line up. Raising interface questions early avoids site modification.
Typically eight to sixteen weeks from approved drawings, depending on instrumentation, controls scope and surface finish requirements. Early agreement on the finish standard and the documentation package is what keeps that date reliable.
Request for quotation
Talk to us about your biotechnology package.
Send drawings, a scope or a sketch and our estimating team in Rayong will answer your enquiry within 48 hours, with a fabrication approach for your biotechnology project. The priced quotation follows once the scope is confirmed.

