Industries / 04

Food & Beverages

Food and beverage plants are judged on cleanliness as much as capacity. K999 fabricates sanitary tanks, process skids, transfer pipework, CIP systems and platforms in 304 and 316L stainless, with orbital welding, hygienic radii and surface finishes that pass inspection under bright light rather than merely looking acceptable.

Food & Beverages fabrication by K999 Thailand

Hygiene and repeatability

Sanitary stainless fabrication for breweries, dairies, sauce plants and beverage lines, welded and finished to a cleanable, bacteria hostile standard.

Hygienic fabrication is about what cannot be seen: crevices at a weld root, a lap joint that traps product, a dead leg longer than two diameters, a radius too tight to clean. We build to a documented weld and finish standard, grinding and polishing internal surfaces to the roughness the client specifies, then passivating and documenting the result.

Tanks, vessels and skids are fabricated from laser cut and rolled sheet, with dished ends, dimple or coil heating jackets, insulation cladding and hygienic manways. Pipework is cut, tacked and orbitally welded in clean conditions, borescoped where required, then assembled into skids with pumps, valves, instruments and cable trays so the line arrives as a tested package rather than a pile of parts.

Documentation covers material certificates, weld logs with welder identification, surface finish reports, passivation records and pressure or leak testing. Where the line must interface with existing plant, we survey the tie in points and fabricate to those dimensions so the installation weekend is a bolt up rather than a rebuild.

What we fabricate

  • Sanitary tanks, vessels and mixing vessels in 304 and 316L
  • Orbital welded hygienic pipework and fittings
  • CIP skids, process skids and pump sets
  • Dimple jackets, coil jackets and insulation cladding
  • Internal polishing, passivation and surface roughness reporting
  • Stainless access platforms, stairs and guarding

Typical applications

  • 01Breweries, distilleries and beverage bottling lines
  • 02Dairies and dairy processing plants
  • 03Sauce, condiment and ready meal production
  • 04Sugar, flour and dry ingredient handling
  • 05Edible oil and tropical fruit processing
  • 06Cold chain and hygienic utility pipework

stainless steel fabrication food industry Thailand / sanitary pipework fabrication / hygienic tank fabrication Thailand / orbital welding food grade / CIP skid fabrication / 316L stainless fabrication Rayong / brewery tank fabrication Thailand / food grade stainless finish and passivation

Food & Beverages FAQs

Questions we are asked

Ten detailed answers on food & beverages fabrication, testing, delivery and documentation.

Mostly 304 and 316L, with 316L used wherever chlorides, cleaning chemicals or product acidity demand it. We also work in Duplex where the duty requires higher strength or corrosion resistance, and we keep stainless handling separate from carbon steel to avoid contamination.

We mechanically polish internal product contact surfaces to the roughness the specification calls for, typically below 0.8 micrometres and finer where required, then passivate and measure. Results are recorded so the finish can be verified rather than described.

Yes. Orbital welding is used on hygienic lines where the diameter allows, with weld parameters recorded for each joint, purge quality controlled and inspection by borescope on request. Manual welds are made by qualified welders to a documented procedure with the same inspection discipline.

We lay out pipework to minimise branch length, keep dead legs within the agreed maximum, slope lines to drain points, use hygienic fittings and radius bends rather than square corners, and position instruments and valves so cleaning flow reaches every surface.

Yes. We build dimple jackets, half pipe coil jackets and conventional jackets, and we apply insulation with stainless cladding where the vessel is exposed in a production area. Jacket pressure testing is included before cladding.

Both. Skids are assembled with pumps, valves, instruments, cable trays, controls and structural frames, then leak tested and prepared for transport. That means the line arrives as one tested package that can be set, connected and commissioned rather than a collection of parts.

Material certificates with heat numbers, weld logs with welder identification, surface finish measurements, passivation records, pressure and leak test certificates, and as built drawings. This supports the client's own food safety and equipment qualification records.

Yes. We survey the existing connections, record flange and clamp details and dimensions, and fabricate spools and supports to suit. Where a line will be tied in during a production stop, we can prepare everything in advance so the window is short.

All openings are capped or sealed, product contact surfaces are protected, and vessels are braced and crated to prevent movement. Internal inspections are recorded before sealing, and the seals stay in place until the client takes delivery.

Yes. Stainless platforms, stairs, handrails and guarding are fabricated with closed sections and drainable details to suit wash down, and we can mill finish or polish surfaces so cleaning is straightforward and corrosion is controlled.

Request for quotation

Talk to us about your food & beverages package.

Send drawings, a scope or a sketch and our estimating team in Rayong will answer your enquiry within 48 hours, with a fabrication approach for your food & beverages project. The priced quotation follows once the scope is confirmed.