Industries / 01
Marine & Offshore
Our Rayong workshop fabricates offshore module steelwork, walkways, riser and conductor guards, boat landings and lifting frames, then delivers them by road to Laem Chabang or Map Ta Phut for shipment. Work is carried out to Australian, American and European offshore standards, with full traceability and third party inspection released before the steel leaves the yard.

Salt, wind and fatigue duty
Offshore module steelwork, platform structures and marine fabrication built to survive salt spray, constant vibration and inspection regimes that never relax.
Marine and offshore packages live or die on the quality of the weld and the accuracy of the fit. A module that misses its interface by ten millimetres becomes a crane lift that cannot happen, and a weld that fails ultrasonic testing six thousand kilometres from the workshop becomes a repair crew on a moving deck. We plan the fabrication around the shipping and installation sequence from the first drawing, so every frame, lug and handrail lands where the lift study expects it.
Our welders work to qualified procedures covering carbon steel, stainless, Duplex and Super Duplex, with post weld heat treatment, hardness testing and corrosion resistant overlays available when the service demands it. Blast and paint systems are applied to offshore specifications including NORSOK M 501 and client specific schemes, with dry film thickness records and holiday testing before dispatch.
Every package is trial assembled where geometry is critical, marked with its lift points and match marks, then packed for ocean freight with sea worth packing, desiccant and shock monitoring on request. Inspection and expediting can be attended in Thailand by the client or their nominated representative, and we issue the full data book with mill certificates, weld maps, non destructive testing reports and paint records.
What we fabricate
- Offshore module and skid structural steelwork
- Riser, conductor and boat landing guards
- Lifting frames, spreader beams and pad eyes
- Walkways, stair towers, gratings and handrails
- Stainless and Duplex pipe spooling for deck services
- Offshore paint systems with NORSOK and client specifications
Typical applications
- 01Platform module steelwork and equipment support frames
- 02FPSO deck structures and process skids
- 03Jetty and mooring hardware, bollards and fenders
- 04Subsea protection structures and mud mats
- 05Shipyard outfitting steelwork and hatch coamings
- 06Marine access platforms and maintenance walkways
offshore fabrication Thailand / marine steel fabrication / FPSO module fabrication / offshore skid fabrication Rayong / boat landing fabrication / Duplex pipe spooling offshore / NORSOK paint system fabrication / platform steelwork fabrication Thailand
Marine & Offshore FAQs
Questions we are asked
Ten detailed answers on marine & offshore fabrication, testing, delivery and documentation.
We fabricate offshore module steelwork, equipment support frames, walkways and stair towers, riser and conductor guards, boat landings, lifting frames and deck skids, plus stainless and Duplex pipe spools for deck services. All of it is built in our Rayong workshop and delivered to Laem Chabang or Map Ta Phut for ocean freight.
Work is normally executed to ASME, AWS D1.1, Australian and European structural standards as the client specifies, with welding procedures qualified under ASME IX. Paint systems follow NORSOK M 501 or the project specific scheme, and inspection follows an approved inspection and test plan.
We model the module and plan the weld sequence before fabrication, use jigs and strongbacks where geometry is critical, and balance welding around the neutral axis of each member. Critical frames are trial assembled in the yard, measured against survey control points and match marked before dispatch.
Yes. Trial assembly is standard on offshore and marine packages where interfaces matter. Modules are assembled on the shop floor, checked for bolt hole alignment, diagonal dimensions, level and interface positions, then match marked and dismantled for transport with the marks recorded on the packing list.
Blast cleaning to the specified surface preparation grade, inorganic zinc or epoxy primer systems, high build epoxy intermediates and polyurethane or polysiloxane finishes, plus hot dip galvanising for smaller items. Dry film thickness is recorded at each coat, and holiday testing is carried out on immersed or splash zone surfaces.
Duplex and Super Duplex welds are made with qualified procedures that limit heat input, control interpass temperature and specify the correct filler, with ferrite content checked on completion. Stainless welds are purged on the root, cleaned between passes and pickled and passivated where the specification requires the passive layer to be restored.
We design and fabricate lifting points to the client lifting study, weld them with qualified procedures, and inspect them before use. Pad eye calculations, weld records and proof load or non destructive testing records are included in the data book so the lift can be approved by the installation contractor.
Finished items are protected with sea worth packing, timber crating or steel frames, desiccant and vapour barrier where specified, and shock or tilt indicators on sensitive assemblies. Flange faces are capped, machined surfaces are greased and protected, and items are marked with lift, weight and centre of gravity information.
Yes. We host client and third party inspectors throughout fabrication, with access to the shop floor, welding, non destructive testing, coating and testing stages. We can also arrange inspection and expediting services in Thailand and neighbouring countries on the client's behalf when travel is not practical.
A typical module or structural package runs eight to sixteen weeks from approved drawings and released material, depending on tonnage, coating system and inspection hold points. Early engagement on the inspection and test plan and on long lead materials is the biggest factor in holding that programme.
Request for quotation
Talk to us about your marine & offshore package.
Send drawings, a scope or a sketch and our estimating team in Rayong will answer your enquiry within 48 hours, with a fabrication approach for your marine & offshore project. The priced quotation follows once the scope is confirmed.

